Anaerobic Adhesives Sealants

TechnotopOGS Anaerobic Adhesives Sealants products


Threadlocking AL-243

Threadlocking AL-243

Surface pre-treatment

In general, Anaerobic Adhesives Sealants Threadlocking AL-243 does not require special pretreatment as slightly oily surfaces (e.g. on as received parts) will be tolerated. However, best results will be achieved on cleaned, degreased parts. If required, the parts should be slightly roughened.

Processing

Threadlocking AL-243 is ready for use and should be applied evenly direct from the bottle/tube with the dispensing tip (avoid direct contact of dispensing tip with metal). For sealing applications, apply Threadlocking AL-243 in circular motions on the thread. Assemble and tighten parts. Do not pour back into the bottle any Threadlocking AL-243 fluid which had contact with metal; even smallest metal particles will cause the content of the bottle to cure. In series construction, the use of manual or automatic applicators is recommended.

Storage

Threadlocking AL 243 can be stored in the unopened original container for at least 24 months at room temperature. Keep away from heat sources and direct sunlight. The air in the bottle/tube keeps Threadlocking AL 243 liquid.

Safety and health

When using products, the physical, safety technical, toxicological and ecological data and regulations in our EC safety data sheets must be observed.

Threadlocking AL-243 download


Anaerobic Adhesives Sealants: Threadlocking AL-270

Threadlocking AL-270

Fluorescent: Yes
For threaded joints up to: M 20 R ¾“
Viscosity at +25°C (+77°F) according to Brookfield: 500 nt mPa·s
Max. gap bridging: 0,15 mm
Breakaway strength (Thread): 28 – 35 Nm
Prevailing stregth: 50 – 65 Nm
Shear strength Nmm² (DIN 54452): 15 – 20 N/mm²
Handling strength at room temperature: 10 – 20 min.
Final strength (100%) after: 3 – 6 h
Temperature resistance: -60 to +150 °C

download 2


Pipe and flange sealing AL-572

Pipe and flange sealing AL-572

Colour: white
Fluorescent: No
For threaded joints up to: M 80 R 3“
Viscosity at +25°C (+77°F) according to Brookfield: 17.000 – 50.000 ht mPa·s
Max. gap bridging: 0,4 mm
Breakaway strength (Thread): 7 – 10 Nm
Prevailing stregth: 2 – 4 Nm
Shear strength Nmm² (DIN 54452): 4 – 6 N/mm²
Handling strength at room temperature: 20 – 40 min.
Final strength (100%) after: 5 – 10 h
Temperature resistance: -60 to +150 °C

download 3


Anaerobic Adhesives Sealants: Thread sealing AL-577

Thread sealing AL-577

Colour: yellow
Fluorescent: Yes
For threaded joints up to: M 80 R 3“
Viscosity at +25°C (+77°F) according to Brookfield: 24.000 – 70.000 ht mPa·s
Max. gap bridging: 0,5 mm
Breakaway strength (Thread): 18 – 22 Nm
Prevailing stregth: 10 – 14 Nm
Shear strength Nmm² (DIN 54452): 6 – 13 N/mm²
Handling strength at room temperature: 15 – 30 min.
Final strength (100%) after: 1 – 3 h
Temperature resistance: -60 to +150 °C

download 4


Retaining cylindrical AL-641

Retaining cylindrical AL-641

Colour: yellow
Fluorescent: Yes
For threaded joints up to: M 20 R ¾“
Viscosity at +25°C (+77°F) according to Brookfield: 550 nt mPa·s
Max. gap bridging: 0,12 mm
Breakaway strength (Thread): 12 – 15 Nm
Prevailing stregth: 17 – 22 Nm
Shear strength Nmm² (DIN 54452): 8 – 12 N/mm²
Handling strength at room temperature: 10 – 20 min.
Final strength (100%) after: 3 – 6 h
Temperature resistance: -60 to +150 °C

download 5